Series Digital Storage Oscilloscopes GDS-2202E

200/100/70MHz Bandwidth Selection; 2 or 4 Channels
1GSa/s Real-Time Sampling Rate for Each Channel (2ch model) ; 1GSa/s Maximum Real-Time Sampling Rate (4ch model)
Per Channel 10M Memory depth and VPO Waveform Display Technology
Waveform Update Rate of 120,000 wfm/s
8 ” WVGA TFT LCD Display
FFT with Maximum 1M points to Provide Higher Frequency Domain Resolution Measurement
High and Low Pass Digital Filter Functions
29,000 Sections of Segmented Memory and Waveform Search Functions
I2C/SPI/UART/CAN/LIN Serial Bus Trigger and Decoding Function
Data Log Function Tracks Signal Changes Up To 100 hours
Provide Remote Internet Storage Function

The GDS-2000E digital oscilloscope features bandwidth selections of 200MHz, 100MH, and 70MHz. Two-channel model provides 1GSa/s real-time sampling rate for each channel; four-channel model provides 1GSa/s maximum real-time sampling rate. The 8-inch 800*480 TFT LCD display and the minimum 1mV/div vertical range allow the GDS-2000E series to measure complex feeble signals and clearly display measurement results.

With respect to the memory depth, the GDS-2000E series digital oscilloscope provides 10M long memory for users to completely retrieve and analyze waveforms. Users, based upon the application requirements, can select 1K, 10K, 100K, 1M or 10M memory depth. Short memory depth collocating with the high sampling rate allows users to observe fast-changing waveforms and, on the other hand, long memory depth aims for continuously changing waveforms. The GDS-2000E series is equipped with waveform search and segmented memory functions to expand the flexible applications of 10M long memory. The segmented memory can be divided the maximum into 29,000 sections for users to bypass any unimportant waveforms so as to swiftly search all required waveforms. With the function, more meaningful waveforms can be saved and target waveforms can be displayed rapidly. With the waveform search function, users can rapidly search desired waveforms according to the required trigger conditions.

General Models

GDS-2072E
- Channels: 2 + External Trigger
- Bandwidth: 70 MHz
- Rise Time (Typical): 5 ns
- Bandwidth Limit: 20 MHz
GDS-2074E
- Channels: 4
- Bandwidth: 70 MHz
- Rise Time (Typical): 5 ns
- Bandwidth Limit: 20 MHz
GDS-2102E
- Channels: 2 + External Trigger
- Bandwidth: 100 MHz
- Rise Time (Typical): 3.5 ns
- Bandwidth Limit: 20 MHz
GDS-2104E
- Channels: 4
- Bandwidth: 100 MHz
- Rise Time (Typical): 3.5 ns
- Bandwidth Limit: 20 MHz
GDS-2202E
- Channels: 2 + External Trigger
- Bandwidth: 200 MHz
- Rise Time (Typical): 1.75 ns
- Bandwidth Limit: Selectable 20 MHz / 100 MHz
GDS-2204E
- Channels: 4
- Bandwidth: 200 MHz
- Rise Time (Typical): 1.75 ns
- Bandwidth Limit: Selectable 20 MHz / 100 MHz

Vertical System

Resolution: 8-bit
Sensitivity Range: 1 mV/div to 10 V/div
Input Coupling: AC, DC, GND
Input Impedance: 1 MΩ // 16 pF approx.
DC Gain Accuracy:
- ±3% (≥2 mV/div)
- ±5% (1 mV/div)
Polarity: Normal & Invert
Maximum Input Voltage:
- 300 Vrms, CAT I
- 300 Vrms, CAT II with 10:1 probe (GTP-070B-4 / 100B-4 / 200B-4)
Offset Position Range:
- ±0.5 V (1–20 mV/div)
- ±5 V (50–200 mV/div)
- ±25 V (500 mV–2 V/div)
- ±250 V (5–10 V/div)

Waveform Signal Processing

Math Functions: +, −, ×, ÷, FFT, FFTrms, User-defined expressions
FFT Settings:
- Points: 1 Mpts
- Window Types: Rectangular, Hamming, Hanning, Blackman-Harris
- Scale: Linear RMS, dBV RMS

Trigger System

Sources: CH1–CH4, EXT* (EXT on 2ch models only), Line
Modes: Auto, Normal, Single Sequence
Types: Edge, Pulse Width (Glitch), Video, Pulse Runt, Rise & Fall, Alternate, Timeout, Event Delay (up to 65535), Time Delay (4 ns–10 s), Bus
Hold-off Range: 4 ns–10 s
Coupling: AC, DC, LF Reject, HF Reject, Noise Reject
Sensitivity: 1 div

External Trigger (2ch Models Only)

Range: ±15 V
Sensitivity:
- DC–100 MHz: ~100 mV
- 100–200 MHz: ~150 mV
Input Impedance: 1 MΩ ±3% // ~16 pF

Horizontal System

Time Base Range: 1 ns/div – 100 s/div (1-2-5 sequence)
ROLL Mode: 100 ms/div – 100 s/div
Pre-trigger: Max 10 divisions
Post-trigger: Max 2,000,000 divisions
Time Base Accuracy: ±50 ppm over any ≥1 ms interval

Acquisition System

Real-Time Sample Rate:
- 1 GSa/s per channel (2ch models)
- Max 1 GSa/s total (4ch models)
Record Length: Max 10 Mpts
Modes: Normal, Average, Peak Detect, Single
Peak Detection: 2 ns (typical)
Averaging: Selectable from 2 to 256

X-Y Mode

X-Axis Input:
- Channel 1 (Channel 3 for 4ch models)
Y-Axis Input:
- Channel 2 (Channel 4 for 4ch models)
Phase Shift: ±3° at 100 kHz

Cursors & Measurements

Cursors: Amplitude, Time, Gating
- Units: s, Hz, degrees, %
Automatic Measurements (36 types):
- Pk-Pk, Max, Min, Amplitude, High, Low, Mean, RMS, Frequency, Period, Rise/Fall Time, Pulse Widths, Duty Cycle, Edges, Pulse Counts, Phase, etc.

Control Panel Functions

Auto Counter: 6-digit, 2 Hz to bandwidth limit
Autoset: Single-button auto setup with undo
Save Setup: 20 sets
Save Waveform: 24 sets

Display

Type: 8″ TFT LCD WVGA color
Resolution: 800 x 480 pixels
Interpolation: Sin(x)/x
Waveform Display: Dots, Vectors, Persistence (16 ms – 4 s), Infinite Persistence
Update Rate: Max 120,000 waveforms/sec
Graticule: 8 x 10 divisions
Display Modes: YT, XY

Interface & Connectivity

USB Ports:
- USB 2.0 High-Speed Host x1
- USB 2.0 High-Speed Device x1
Ethernet: RJ-45, 10/100 Mbps with HP Auto-MDIX
Go-NoGo Output: BNC, 5V max / 10 mA TTL open collector
Security: Kensington-style lock slot

Miscellaneous

Multi-language Menu: Available
Online Help: Available
Time Clock: Date/Time for saved data
Dimensions: 384 mm x 208 mm x 127.3 mm
Weight: 2.8 kg
Operating Environment:
- Temperature: 0°C to 50°C
- Humidity: ≤80% (≤40°C), ≤45% (41–50°C)

Digital Storage Oscilloscopes, Oscilloscopes, Test & Measurement

HDO6000 / HDO6000-MS High Definition Oscilloscopes

Condition	New

Digital Storage Oscilloscopes, Oscilloscopes, Test & Measurement

HDO8000 High Definition Oscilloscopes

Condition	New

Oscilloscopes, Real-Time & Digital Oscilloscopes, Test & Measurement

HM1008-2

Condition	New

Accessory

User Manual CD x1, Power Code x1
GTP-070B-4
70MHz (10:1/1:1) Switchable passive probe for GDS-2072E/2074E (one per channel)
GTP-100B-4
100MHz (10:1/1:1) Switchable passive probe for GDS-2102E/2104E (one per channel)
GTP-200B-4
200MHz (10:1/1:1) Switchable passive probe for GDS-2202E/2204E (one per channel)

Optional Accessories

GRA-426
Rack Adapter Panel
GAK-003
50 ohm Impedance Adapter
GSC-008
Soft Carrying Case
GTL-246
USB Cable, USB 2.0, A-B Type, 1200mm
GTL-110
Test Lead, BNC-BNC Heads
GDB-03
Oscilloscope Education & Training Kit
GCP-300 Current Probe, DC ~ 300kHz, 200A
GCP-500 Current Probe, DC ~ 500kHz, 150A
GCP-1000 Current Probe, DC ~ 1MHz, 70A
GCP-1030
Current Probe, DC ~ 100MHz, 30Arms
GCP-206P
Current Probe – Power Supply, 2 Channel Power Supply for GCP-530/1030
GCP-245P
Current Probe – Power Supply, 4 Channel Power Supply for GCP-530/1030
GCP-530
Current Probe, DC ~ 50MHz, 30Arms
GDP-025
Differential Probe, 25M High Voltage Differntial Probe
GDP-050
Differential Probe, 50M High Voltage Differntial Probe
GDP-100
Differential Probe, 100M High Voltage Differntial Probe
GTP-033A
Oscilloscope Probe, 35MHz 1:1 Passive Probe, BNC(P/M)

Series Digital Storage Oscilloscopes GDS-2202E